+ Reply to Thread
Page 2 of 16 FirstFirst 1 2 3 4 12 ... LastLast
Results 11 to 20 of 155

Thread: Range Report Vector V53K not good!!

  1. #11
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    LP?

  2. #12
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    Ahh, lower pack? SUO semi.

  3. #13
    Gets the Shakes if No HK Contact in 24 Hour Period
    Jesser's Avatar
    Join Date : Apr 2011
    Location : Tulsa, OK
    Posts : 540

    Default

    No LP= locking piece.... What number locking piece is in the bolt group

  4. #14
    Desperately Needs Treatment

    Join Date : Feb 2010
    Posts : 1,183

    Default

    ^^^^^^^^ that. Locking Piece / LP

  5. #15
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    Got it , I will check and then post the number that is one there.

  6. #16
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    OK, here are the numbers: it should be noted that one one side of the mag well, it is stamped V93 then the other side 53K.

    The bolt, not sure if that is what it is called, the small silver piece that the locking piece fits into is marked 003337 and BW.

    The LP is a #15.

    Does this help understand what is happening with this weapon?

    Thanks for all your help guys!

  7. #17
    Desperately Needs Treatment
    bystok's Avatar
    Join Date : Nov 2008
    Location : GA
    Age : 42
    Posts : 1,253

    Default

    how high does the ejector lever sit in the bolt head when the cocking lever is pulled to the rear? New Vectors seem to be notoriously bad for having low shelves and therefore not getting the ejector in position to remove the spent round......pull the cocking lever to the rear and see if the ejector is high up in the channel in the bolt head or if there is a gap

    I would not waste my time sending it back to Vector......send it to Ghillie and get it done right if you can't get it running.......I bet it will work and look a heck of a lot better than the finish on it now!!!!!!!!!!!!!!!!!

  8. #18
    Desperately Needs Treatment
    HKaltwasser's Avatar
    Join Date : Feb 2009
    Location : Dripping Springs, Tx- Just west of weird.
    Posts : 1,154

    Default

    Quote Originally Posted by travelinscout View Post
    OK, here are the numbers: it should be noted that one one side of the mag well, it is stamped V93 then the other side 53K.

    The bolt, not sure if that is what it is called, the small silver piece that the locking piece fits into is marked 003337 and BW.

    The LP is a #15.


    Does this help understand what is happening with this weapon?

    Thanks for all your help guys!
    I wouldn't be so sure that it's a #15 LP. They ground down #8's and re-marked them as #15 at least this is how mine appeared to be done. Doesn't look anything like my german #15 LP. This could be the problem, just a guess though.

  9. #19
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    My first thought was to send it to Vector because it is under warranty. After what I spent on the gun I don't think I should have to spend any more money just to get it to function...

  10. #20
    HKPRO Professional
    travelinscout's Avatar
    Join Date : Feb 2009
    Location : Arizona
    Posts : 361

    Default

    Just spoke to Vector and they were very friendly. They said that the K models are notorious for needing to be broken in and that I should try another 100 rounds or so of steel case ammo. If after that, it is still malfunctioning they said they would be happy to take it back and look at it, no cost to me. Thoughts??

+ Reply to Thread
Page 2 of 16 FirstFirst 1 2 3 4 12 ... LastLast

Links

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Search tags for this page

bolt gap mp5
,
hk bolt gap
,
receiver bulge
,
sse weapons
,
sse weapons c93
,
v53k
,
vector 53
,
vector arms v53k
,
vector quality
,

vector v53k

,
vector v53k accuracy
,
vector v91 review
Click on a term to search for related topics.