Well I did it ....
Results 1 to 8 of 8
Like Tree5Likes
  • 2 Post By Glocking26
  • 1 Post By sean415
  • 1 Post By AGG
  • 1 Post By Disregarded9-side

Thread: Well I did it ....

  1. #1
    Junior Member
    Glocking26's Avatar
    Join Date : Sep 2019
    Location : Glen Mills Pa.
    Posts : 29
    Mentioned
    0 Post(s)

    Default Well I did it ....

    Two hours later and scared I’d screw it up I got that dam thing out of my SP5K mag well with no damage. What a pain in the ass!!!
    Attached Thumbnails Attached Thumbnails Well I did it ....-3e558058-7a34-4851-9766-a007a1c204a0.jpeg  
    GuntherRommel and TLOU_Joel like this.

  2. #2
    Unrepentant HKHolic
    sean415's Avatar
    Join Date : Feb 2012
    Location : PA
    Posts : 2,239
    Mentioned
    21 Post(s)

    Default

    Now you’re “Koching”
    AGG likes this.

  3. #3
    Gets the Shakes if No HK Contact in 24 Hour Period
    Domino's Avatar
    Join Date : Sep 2017
    Posts : 995
    Mentioned
    8 Post(s)

    Default

    Well Done.
    HK - No Compromise

  4. Remove Advertisements
    HKPro.com
    Advertisements
     

  5. #4
    Member

    Join Date : Aug 2019
    Posts : 55
    Mentioned
    0 Post(s)

    Default

    Nice, patience pays off

  6. #5
    AGG
    AGG is offline
    Unrepentant HKHolic
    AGG's Avatar
    Join Date : Feb 2007
    Location : Alabama
    Posts : 32,816
    Mentioned
    223 Post(s)

    Default

    Congratulations--- Deep State microphone???

    Tony
    GuntherRommel likes this.

  7. #6
    Gets the Shakes if No HK Contact in 24 Hour Period
    Disregarded9-side's Avatar
    Join Date : Mar 2009
    Location : North Carolina
    Posts : 524
    Mentioned
    4 Post(s)

    Default

    Quote Originally Posted by AGG View Post
    Deep State microphone[/B][/U]???
    That's the wrong episode of Ancient Aliens; we just put tracking devices in the space where the second pin would normally go.
    AGG likes this.
    Never forget;
    Rebellion to tyrants is obedience to obedience to God.

  8. #7
    Senior Member

    Join Date : Sep 2012
    Posts : 115
    Mentioned
    1 Post(s)

    Default

    Good job. I get frustrated with things like that quickly. What did you do to get it out?

  9. #8
    Junior Member
    Glocking26's Avatar
    Join Date : Sep 2019
    Location : Glen Mills Pa.
    Posts : 29
    Mentioned
    0 Post(s)

    Default

    Quote Originally Posted by cc561 View Post
    Good job. I get frustrated with things like that quickly. What did you do to get it out?
    I put the upper in a gunsmith vice and wrapped the entire gun with painters tape so it didn’t get scratched or get marks from the sparks of the Dremel tool. With a very steady hand and I mean very steady I started making small cuts on the steel block Which is actually round. I started turning it. it will turn in the holes that it’s recessed into. Cut turn cut turn about an hours and a half of that then it popped out. It was not a fun project but it’s something I just had do. The paddle release will be delivered tomorrow:)

Sponsored Links

 
 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •