P2000/SK/USPC LEM Trigger Job Part 1
Page 1 of 55 1 2 3 11 51 ... LastLast
Results 1 to 10 of 541
Like Tree1Likes

Thread: P2000/SK/USPC LEM Trigger Job Part 1

  1. #1
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default P2000/SK/USP/C LEM Trigger Job Part 1

    I have been asked to repost the thread showing how to do the V2 to V4 and V1 trigger job on the USP/C LEM, P2000 LEM, and P2000SK LEM, so here it is again.

    To lighten LEM trigger (USPC, USP, P2K or P2KSK) you need Trigger Rebound Spring and Firing Pin Block Spring to drop the pull to approx. 5 pounds. Price of these parts is 4.50 each, plus shipping.
    Firing pin block spring # 214192
    Trigger return spring # 214164
    These parts are the same parts used in the non-LEM USP and USPC variants.

    edited to add updated part numbers
    To lighten the LEM pull on the USP/C pistol you will need part numbers
    214192 Firing pin block spring USP/C if the gun was made before 2005
    209296 firing pin block spring for guns made 2005 or later.
    209266 Trigger return spring

    According to HK, the following is needed to lighten the trigger pull on the P2000. You will need part numbers:
    209296 Firing pin block spring
    209266 Trigger return spring
    These parts should eliminate the sluggish trigger return some have reported when releasing the trigger slowly but will also make the trigger pull slightly heavier.

    However, note that this trigger job was done on the P2K/SK using the first part numbers listed in this post. That pistol is either an AD or an AE (03 or 04) so when doing the LEM trigger job on a pre-05 use the first part numbers listed originally, but if 05 (AF) or later use the new part numbers.





    Join the NRA
    On the 8th day God created HKs.
    Beware speaking with a sharp tongue as you are apt to cut your own throat.

  2. #2
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default Part 2





  3. #3
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default Part 3





  4. Remove Advertisements
    HKPro.com
    Advertisements
     

  5. #4
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default Part 4





  6. #5
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default Part 5





  7. #6
    Junior Member

    Join Date : May 2006
    Location : Northern VA, USA
    Age : 67
    Posts : 7
    Mentioned
    0 Post(s)

    Default

    I think this should be a sticky.
    It's not who you know..... it's what you know about who you know.

  8. #7
    Junior Member
    A6Gator's Avatar
    Join Date : May 2006
    Location : Memphis, TN
    Posts : 5
    Mentioned
    0 Post(s)

    Default

    Excellent!

  9. #8
    Junior Member

    Join Date : Feb 2005
    Posts : 1
    Mentioned
    0 Post(s)

    Default LEM Trigger lightening

    Mr BigBore,

    EXCELLENT post! More explanative than the Armorer's Manual!

    I have a Compact .45 with the LEM trigger. Tommy Thacker did the trigger job on that, and he did a whale of a job - it's slicker than grease on glass. But would it be possible for you to post the same type of trigger job explanation, WITH PICTURES (I'm a picture lovin' kind of guy - I need to see what I'm yanking and banking on) for the LEM Compact .40 and .45 series?

    Thanks again for a super post.

    Mike

  10. #9
    Desperately Needs Treatment
    MaverickH1's Avatar
    Join Date : Jan 2006
    Location : Virginia
    Age : 33
    Posts : 1,185
    Mentioned
    0 Post(s)

    Default

    Sweeeeeet :)

  11. #10
    Unrepentant HKHolic
    Big Bore's Avatar
    Join Date : Jan 2002
    Location : Finally back in Indiana!
    Posts : 2,788
    Mentioned
    0 Post(s)

    Default

    It would be almost the same for the USP/C LEM as it would be for the P2K/SK. The only real difference would be the lack of the right side slide release. Honestly, I don't think the differences would be worth the effort nor do I own a USP/C in LEM in which to convert. As much as the variant change helped the P2K/SK LEM I still do not like the LEM trigger as much as I do the normal V1 (SA/DA safe/decock) of the USP/C variety.

Page 1 of 55 1 2 3 11 51 ... LastLast

Sponsored Links

 
 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Search tags for this page

h&k p2000 trigger job
,
h&k p2000sk trigger job
,
hk lem trigger job
,
hk p2000 trigger
,

hk p2000 trigger job

,
hk p2000 trigger kit
,
hk p2000sk trigger job
,
hk usp firing pin
,
hkp2000 trigger job
,
p2000 trigger
,

p2000 trigger job

,
video on p2000 trigger return spring change
Click on a term to search for related topics.