Hi guys... wanted to post on my first HK like weapon build ever... I'm a virgin, and this is my first post here, so be kind.:wink:
I ordered these parts for it:
US made Hammer, Sear, and Trigger (HK Parts)
US made Foregrip, with 2 two inch picatinny rails (HK Parts), with a TAL-4 Virtical grip.
UTG Second Gen STANAG quick disconect claw mount, (Amazon)
US made Grip... the one from HK Parts, but I got it in a trade.
C-More Railway 8MOA Red Dot, (Optics Planet)
A3 Retractable Stock (HK Parts)
When I fitted the UTG mount, I had to file the feet of the mount, and the saddle on the reciever (Did this with a needle file.... was a lot of work)...BTW, the marks are from the UTG itself.... before I figured out how to operate the locking mechanism. /doh
It now takes about 12 to 15 lbs of force to lock the mount on... maybe a little more.
I added the C-More Railway...
Here is where I milled the back of the reciever and the grip, where they come together... and later I milled a little out of the stock itself, so that they match up well enough to put the retaining pin in by hand.... The last 1/4 inch requires a good bit of force... but I don't "HAVE" to have a hammer to put it in.
As you can tell, I really didn't care that much what the inside of the A3 Stock looked like, I'll throw on a little paint, and it will be good to go.
Next I added a small 2 inch rail to the Foregrip, on the right side, just like the one that was on the bottom. (This will be for a cheap "Pistol" version of a light/Laser Combo, to throw on if I use it for protection at the house at night. The pistol versions will serve adequately, and they are quick disconnect for ease of convenience.)
Then I added the TAL-4 Foregrip on the bottom.
I recieved the trigger, sear, and hammer today.... She is 922r compliant now and I will start milling the bars out of the magazine well tomorrow,... hopefully...
Here is a couple of pics how she sits atm....enjoy.
After the milling and refinishing is over... I plan on turning it into an SBR... Adding a can after that, then going for Class III greatness....
This is gonna take a while.....
I ordered these parts for it:
US made Hammer, Sear, and Trigger (HK Parts)
US made Foregrip, with 2 two inch picatinny rails (HK Parts), with a TAL-4 Virtical grip.
UTG Second Gen STANAG quick disconect claw mount, (Amazon)
US made Grip... the one from HK Parts, but I got it in a trade.
C-More Railway 8MOA Red Dot, (Optics Planet)
A3 Retractable Stock (HK Parts)
When I fitted the UTG mount, I had to file the feet of the mount, and the saddle on the reciever (Did this with a needle file.... was a lot of work)...BTW, the marks are from the UTG itself.... before I figured out how to operate the locking mechanism. /doh
It now takes about 12 to 15 lbs of force to lock the mount on... maybe a little more.
I added the C-More Railway...
Here is where I milled the back of the reciever and the grip, where they come together... and later I milled a little out of the stock itself, so that they match up well enough to put the retaining pin in by hand.... The last 1/4 inch requires a good bit of force... but I don't "HAVE" to have a hammer to put it in.
As you can tell, I really didn't care that much what the inside of the A3 Stock looked like, I'll throw on a little paint, and it will be good to go.
Next I added a small 2 inch rail to the Foregrip, on the right side, just like the one that was on the bottom. (This will be for a cheap "Pistol" version of a light/Laser Combo, to throw on if I use it for protection at the house at night. The pistol versions will serve adequately, and they are quick disconnect for ease of convenience.)
Then I added the TAL-4 Foregrip on the bottom.
I recieved the trigger, sear, and hammer today.... She is 922r compliant now and I will start milling the bars out of the magazine well tomorrow,... hopefully...
Here is a couple of pics how she sits atm....enjoy.
After the milling and refinishing is over... I plan on turning it into an SBR... Adding a can after that, then going for Class III greatness....
This is gonna take a while.....