HKPRO Forums banner

1 - 20 of 267 Posts

·
Vendor
Joined
·
282 Posts
Discussion Starter #1 (Edited)
At present we have about 120 barrels spoken for so in this thread I will offer the last 50 to whomever speaks for them first
we will start the count at 121 and end at 170
if we get that far I will start a new lot of barrels and I should have a estimate of when I can expect them to be available

the cost for the barrels are 445.00 and we require you to contact us at [email protected]
at that point we will email you back a copy of our barrel pre-order form for you to fill out and mail back to us with a deposit of 75.00 for each barrel

we expect to be sending the current lot of barrels out in mid October this is our best guess
we hit a few snags on our original estimate but things are running smother now
 

·
The Librarian
MP5-N and HK23E-K
Joined
·
5,465 Posts
For anyone who hasn't been following this, below are your choices of barrel configurations and they are Chrome Lined!!!!

16" IAR Profile Barrel
16" MR556 Profile Barrel
14.5" M4 Profile Barrel
10.4" Standard Contour Barrel
10.4" Light Contour Barrel
9" 416C Profile to be determined

Hammer Forged 1:7 twist Blank, Chrome lined bore, heavy Magnesium Phosphate finish.
 

·
Premium Member
Joined
·
2,677 Posts
Deposit sent on two of them.
 

·
Registered
Joined
·
7 Posts
Would anyone kindly chime in on the differences between the Standard and Light contours? Any meaningful differences between them?
 

·
Registered
Joined
·
19 Posts
Would anyone kindly chime in on the differences between the Standard and Light contours? Any meaningful differences between them?
The light will be a few ounces lighter just because of the different contour from barrel extension to gas block as pictured above (assuming those are both 10.4" in the picture). Other than that I can’t imagine much difference but I could be wrong.
 

·
Registered
Joined
·
7 Posts
The light will be a few ounces lighter just because of the different contour from barrel extension to gas block as pictured above (assuming those are both 10.4" in the picture). Other than that I can’t imagine much difference but I could be wrong.
Thanks - makes sense that weight would be the only difference. I was just worried that there might be some hidden impact on gasblock configuration.
 

·
Vendor
Joined
·
282 Posts
Discussion Starter #18
Is there a way to get 10” LW barrel w/ the correct size gas port for a vented 10” GB? If so, I’ll take 1. Do you take CCs or PP?
I can build the barrel to spec
I have about 100 un-vented gasblocks that can be machined to the right size to function properly with a 10.4" barrel this is a product that I plan on selling
DSCN8760.JPG
8761.jpg
 

·
Registered
Joined
·
3,182 Posts
@nefariousarms

When is the last time we have to give spec on our 10.4” barrels for 3mm or 5mm indexing?

And what if I already have my own OEM vented gas blocks for them?
 
  • Like
Reactions: aksog

·
Vendor
Joined
·
282 Posts
Discussion Starter #20
@nefariousarms

When is the last time we have to give spec on our 10.4” barrels for 3mm or 5mm indexing?

And what if I already have my own OEM vented gas blocks for them?
The gasblock will be a separate item for sale to those that need them for the clone barrels we are making and they will be available for individual sale

it is my understanding that the 10.4" barrels need a gasport specific to the gasblock that will be used and if the rifle is to be used with a suppressor
the gasport will not be drilled into the barrels until this information is received from the buyer prior to shipment
we intend to ask for this information when we send out our notification for the remaining balance remittance.

the 3mm index pin will be the standard configuration but the barrel extension can be modified to work with other upper receivers
 
1 - 20 of 267 Posts
Top